Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

F37 Modified Silicone Polyether

A base chemistry for defoamer manufacturing: allyl ethers of different HLB values grafted onto low-hydrogen silicone with high-cloud-point polyoxyethylene ether. Water-soluble, low in silicone, high flash point.

Models: F37Form: Water-soluble liquid (≥95% active)Type: Raw Materials

Overview

These grades are made by grafting allyl ethers of different HLB values onto low-hydrogen silicone together with high-cloud-point polyoxyethylene ether and polysiloxane, then processing the mix into a water-soluble liquid. Poured in during crude extraction, transport, refining or delayed coking, it clears the bubbles that form along the way, at a small dose and with inhibition that lasts. Natural-gas fields, offshore platforms and vacuum-residue delayed coking units are where it earns its place. Silicone content is kept low, which gives a safer handling profile without costing you foam control. The base itself is low-foaming, emulsifies strongly and holds up at both high and low temperature.

Key advantages

Low-foaming, with strong emulsifying power
Holds at both high and low temperature
Foam control built into the chemistry
Low silicone content for safer handling
Flash point above 80 °C

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

PropertyF37
AppearanceTransparent to pale yellow oily liquid, slight alcoholic odour
Active content≥95.0
Viscosity (25 °C, mPa·s)100-1000
pH5.0-7.5
Density (g/cm³)0.95-1.05
Flash point (°C)>80

Recommended applications

  • Defoamer manufacturing
  • Crude oil extraction
  • Refining and delayed coking
  • Gas field and offshore production

What decides the model

Active content, molecular weight and the ratio inside the material decide what you can build from it. Two materials with the same name can differ in the ratio that governs how the finished emulsion behaves, so the table columns are the specification you formulate against.

This family is published as a single model, so there is no internal comparison to make: the table above is the whole of the data we release on it.

How to trial these models

These are base chemistries for formulators rather than finished defoamers, so the trial is a formulation trial. Run it against the concentrate you intend to build: check how the material disperses, whether the emulsion stays stable over the shelf life you need, and whether the active content you calculate from the table matches what the finished batch delivers. Keep a small sample of the reference concentrate so the comparison is like for like.

Questions buyers ask about F37

What is the difference between the F37 models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much F37 do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a defoamer raw material can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of F37?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a F37 shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

1000 kg IBC tote of f37 modified silicone polyether staged for dispatch

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Raw Materials Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.