Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

Foam Control on Paper-making Lines: Why Dosing Alone Does Not Hold It Down

Foam on a paper machine is never fully eliminated. The mill keeps dosing and the foam keeps coming back. The cause is usually in the process, not the drum.

By the ElonMek technical team · Application Guide · Published 2026-09-30

Wet end of a paper machine with white water running below the wire

On a paper machine, foam is a permanent nuisance you can never quite get rid of. It slows pulp transport, upsets level control and cuts dewatering. On the sheet it leaves pinholes and spots, and at worst it tears the web.

Most mills answer it the same way. When foam surges, add defoamer. When the improvement fades, add more. The cost of defoamer per ton of paper climbs year after year, the process still swings, and new sheet defects keep appearing.

That pattern is not bad luck. Three causes sit behind it, and all three are easy to miss.

Foam Breaking and Foam Inhibition Are Not the Same Job

Most defoamers knock down foam that is already there, and they look excellent in a lab beaker or a short trial. On a line that runs continuously, foam keeps being born. Air is pulled in all the time as white water circulates, the surfactants in the pulp hold the bubbles together, and high-shear equipment grinds them finer still.

Breaking foam fast only deals with the foam you have, and does nothing about the foam that is coming. What decides the outcome on site is the foam-inhibition time, measured in hours or a whole shift. If the defoamer cannot stay stable in the white water and its actives decay quickly, you are dosing again every hour or two.

Operators usually put that down to a poor product. The real reason is that selection looked at how fast the defoamer breaks foam and skipped the number that counts: how long it keeps working.

When the Process and the Product Do Not Match

Conditions swing widely from one section of the mill to the next. Each family of actives, whether polyether, silicone, mineral oil or higher alcohol, has its own window for temperature, pH and electrolyte concentration.

In the pulping section, black liquor from alkaline cooking usually runs above 70 °C at pH 12-13. Some silicone-based defoamers demulsify under that combination of sustained heat and strong alkali. The actives drop out, lose their defoaming power, and can even form an oily deposit. Where that happens, a higher dose just fouls the system faster.

At the paper-forming end the white water is cooler. It does not help. The wire and press sections apply hard shear and dewatering, and some polyether-based defoamers lose performance below 50 °C. They can separate, float or precipitate, then deposit on white-water pipe walls and wire parts, and on a high-speed machine that is how a web break starts.

The same defoamer can sail through Paper Machine A and fail time and again on Paper Machine B. That is not a defective batch. It is a formula that does not fit the conditions.

How the Defoamer Interacts With Everything Else

Modern white water is a crowded place. Sizing agents, retention aids, wet-strength agents, dyes and fillers all share it. The defoamer is one more auxiliary in that mix, and it will react with the others.

When the defoamer does not fit, the troubles are familiar:

  • Hydrophobic deposits foul equipment and trigger faults, which means more web breaks and more shutdowns for cleaning
  • Wet-end chemistry is disturbed, retention aids stop working, sizing drops and the sheet takes up more water
  • Severe sheet defects appear, from holes and transparent spots to oil stains and black specks
  • Closed white-water circulation and wastewater treatment both suffer

A Different Approach: Match the System Instead of Over-dosing

Three objectives drive it: long-term foam inhibition, compatibility with the system, and low interference with everything else.

The troubles above point to one thing. Foam that keeps returning and defoamer consumption that keeps rising do not have to mean a bad defoamer. More often the wrong formula has been aimed at the wrong conditions.

A defoaming solution that actually holds has to do three things at once:

  • Hold foam back for the long run, so the actives stay stable through high temperature, strong alkali or heavy shear and restrain new foam continuously while re-dosing drops away
  • Fit the system, with active ingredients and an emulsification system chosen or compounded for the machine against its temperature, pH, pulp type, speed and chemical profile, so there is no demulsification, floating oil or deposition
  • Interfere as little as possible, staying compatible with the other chemicals in the system and avoiding flocculation, wire clogging and any harm to the physical properties of the sheet

The approach to paper-making defoaming rests on those three criteria. Before any product leaves, it is tested under conditions that copy the real process, not just the standard data taken in room-temperature pure water.

Foam on a paper machine can be managed, and managed systematically. Treat the defoamer as a technical solution built for that machine rather than a consumable you keep tipping in, and the cycle of over-dosing and unexplained sheet defects loses most of its force.

Keep reading

Related guides

All technical guides

Range

Grades used in this application

All 64 grades

Markets

Buying from Southeast Asia?

The same grade families are supplied to textile, paper and construction plants in Vietnam, Cambodia and Laos.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.