Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

681F High-Temperature Self-Emulsifying Oilfield Defoamer

Co-developed with major domestic oilfields. It self-emulsifies, leaves no oil ring and no floating solids after high-temperature water dilution, and holds without layering on long storage.

Models: 681FForm: Self-emulsifying emulsion (≥45% active)Type: Oilfield

Overview

Built with major domestic oilfields and backed by long field experience, this is a self-emulsifying high-temperature defoamer based on grafted silicone polyethers and specially modified polysiloxanes. It handles high-temperature foaming systems across the board and kills foam fast in crude extraction, filtration and gathering, with a clear effect on oil recovery rate — most of all in high-water-cut, high-salinity wells and on offshore platforms, in separation and filtration, where high-temperature inhibition holds up. It self-emulsifies and dilutes well in water, leaves no oil ring and no suspended solids after high-temperature water dilution, and does not break emulsion or layer on long storage. It is environmentally friendly with no pollution and also helps cut viscosity, and the structure can be tuned to different foaming systems — high-viscosity, weak-acid strong-alkali and heavy-salt among them.

Key advantages

Self-emulsifies and dilutes easily in water
No oil ring or suspended solids after high-temperature dilution
No emulsion breakdown, no layering on long storage
Environmentally friendly, no pollution, with viscosity reduction
Structure can be tuned to the foam system
Inhibition improves as liquid temperature rises

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

Property681F
AppearanceWhite emulsion
Active content≥45.0
Viscosity (25 °C, mPa·s)600-2500
Ionic typeWater-soluble non-ionic

Recommended applications

  • Crude oil extraction
  • Filtration and gathering
  • Seawater desalination
  • Microbiological water treatment
  • Mining and screening separation
  • High-salinity, high-water-cut and high-pressure wells
  • Offshore platform production

What decides the model

Flash point and compatibility with the produced fluid decide the choice here, not the defoaming speed. A grade that defoams brilliantly but flashes low, or that emulsifies with the crude, cannot be used on a separator train.

This family is published as a single model, so there is no internal comparison to make: the table above is the whole of the data we release on it.

How to trial these models

Oilfield grades are specified for high flash point and for compatibility with produced fluids, so the trial has to be run on the actual wellstream or separator fluid rather than on water. Where a demulsifier is already in the system, dose the defoamer after it: the two chemistries compete for the same interface, and dosing order is often the difference between a clean separation and a rag layer.

Questions buyers ask about 681F

What is the difference between the 681F models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much 681F do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a oilfield-grade defoamer can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of 681F?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a 681F shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

200 kg plastic drums of 681f high-temperature self-emulsifying oilfield defoamer on the loading dock

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Oilfield Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.