Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

663-10 / 663-20 / 6557 High-Content Silicone-Polyether Defoamer

An emulsion defoamer built from modified polysiloxane and high-carbon polyether. It is at its strongest in pulp making, black liquor washing and landfill leachate.

Models: 663-10663-206557Form: Silicone-polyether emulsionType: Silicone & Ether

Overview

663-10, 663-20 and 6557 are emulsion defoamers synthesised from modified polysiloxane and a high-carbon polyether emulsion. They are aimed at foaming systems in pulp making, black liquor washing and landfill leachate. They break foam fast, disperse well, keep in storage, and release entrained air well.

Key advantages

Breaks foam fast
Disperses well
Keeps well in storage
Releases entrained air well
High active content

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

Property663-10663-206557
AppearanceWhite emulsionWhite emulsionWhite emulsion
Active content30.0±1.033.0±1.033.0±1.0
Viscosity (25 °C, mPa·s)200-1500300-1800300-1800
pH5.5-7.55.5-7.55.5-7.5
Ionic typeNon-ionicNon-ionicNon-ionic

Recommended applications

What decides the model

Surface tension and active content decide most of it: a higher active content buys a lower dose, while the silicone-polyether block structure decides how well the grade survives heat and high shear. Ionic type matters next, because it has to match the charge of the system you are adding it to.

Across the 3 models in this family the published active content runs from 30.0±1.0 to 33.0±1.0. The table above is the only figure we publish, and it is typical rather than a specification.

How to trial these models

Silicone and silicone-polyether grades settle the foam by lowering surface tension, so the dose that works is usually small and the risk is over-dosing rather than under-dosing. Split an already-made batch, add the grade in steps of 10 ppm up to the dose you would accept commercially, and read foam height at one minute and at ten minutes. Watch the surface as well as the foam: a silicone grade pushed too far shows as fish eyes, craters or loss of gloss before it shows as any change in the foam.

Questions buyers ask about 663-10

What is the difference between the 663-10 / 663-20 / 6557 models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much 663-10 do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a silicone & ether defoamer can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of 663-10?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a 663-10 shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

200 kg plastic drums of 663-10 / 663-20 / 6557 high-content silicone-polyether defoamer on the loading dock

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Silicone & Ether Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.