Factory-direct manufacturer · Tianjin, China · 6 defoamer types, 64 categories, 114 models

118G / 208G / 418G High-Efficiency Silicone Powder Defoamer

A silicone powder defoamer for dry-mix systems. The active rides on a solid carrier, so it survives high electrolyte, strong acid, strong alkali and high shear, where ordinary silicone emulsions give up.

Models: 118G208G418GForm: Solid powderType: Silicone & Ether

Overview

A solid defoamer built from several modified polydimethylsiloxanes and other high-performance components. Because it is a powder, the active is carried into the foaming system on a solid carrier. That gets around the usual failure of silicone emulsions: in high-electrolyte, strong-acid, strong-alkali or high-shear systems the emulsion breaks and the active agglomerates fast. The result is fast foam break, long inhibition and low cost in use. It is also easy to handle. Blend it straight into solid powder products such as solid metal cleaners and washing powder. Low moisture content keeps it stable in storage and transport and tolerant of environmental and temperature swings.

Key advantages

Breaks foam fast
Long inhibition period
Holds up in electrolyte, acid, alkali and high shear
Blends straight into dry powders
Low moisture content: stable in storage and transport

Typical properties

Each model below represents a different internal structure. Select the model that matches your foaming system. Values are typical and indicative, not a specification.

Property118G208G418G
AppearanceWhite powderWhite granulesWhite granules
Active content20.0±1.020.0±1.020.0±1.0
pH6.0-8.56.0-8.56.0-8.5

Recommended applications

What decides the model

Surface tension and active content decide most of it: a higher active content buys a lower dose, while the silicone-polyether block structure decides how well the grade survives heat and high shear. Ionic type matters next, because it has to match the charge of the system you are adding it to.

The models in this family differ in the properties tabulated above; those columns, rather than a product name, are what a shortlist has to be built on.

How to trial these models

Silicone and silicone-polyether grades settle the foam by lowering surface tension, so the dose that works is usually small and the risk is over-dosing rather than under-dosing. Split an already-made batch, add the grade in steps of 10 ppm up to the dose you would accept commercially, and read foam height at one minute and at ten minutes. Watch the surface as well as the foam: a silicone grade pushed too far shows as fish eyes, craters or loss of gloss before it shows as any change in the foam.

Questions buyers ask about 118G

What is the difference between the 118G / 208G / 418G models?
All of them share the same base chemistry. They differ in active content, viscosity and sometimes ionic type, and the difference matters when your system runs hot, sheared or at low pH. The property table above lists the values for each model; send us your process data and we will tell you which one to trial first.
How much 118G do I dose?
It depends on the foam load, so treat any figure as a starting point: most customers begin between 0.1% and 0.5% on formulation weight for water-based systems, then tune up or down. Overdosing a silicone & ether defoamer can create its own stable foam, so add in steps rather than all at once.
Can you send a sample of 118G?
Yes. Standard liquid grades are usually available from stock and we can arrange a sample with the data sheet and safety data sheet. Tell us the application, your operating temperature and current dose, and our technical team will run a shake-down test and come back with a model and a recommended dosage.
What documents come with a 118G shipment?
Every order ships with a certificate of analysis (COA), the technical data sheet (TDS) and the safety data sheet (MSDS/SDS). A certificate of origin can be issued on request for customs clearance.

Packaging and storage

Supplied as a non-hazardous good. Liquid models are packed in 25, 50 and 200 kg plastic drums or 1000 kg IBC totes; powder models in 20 kg cartons. Shelf life is 12 months in a sealed container, stored indoors and away from direct sunlight. Mix or shake before use; if diluted before use, use the diluted product within the same shift.

25 kg cartons of 118g / 208g / 418g high-efficiency silicone powder defoamer shrink-wrapped on a pallet

Ordering and logistics

  • Samples. Standard liquid grades are usually in stock; sample quantities ship with the certificate of analysis, technical data sheet and safety data sheet so your lab can run trials before you commit.
  • First orders. Trial production runs start from a single drum or one IBC tote, so the product can qualify on your line before volume purchasing.
  • Lead time. Stock grades ship within days; new production batches are scheduled around your first shipment date and confirmed on the quotation.
  • Trade terms. Quotations on FOB Tianjin or CIF your port, with export documents prepared for sea, air or courier freight.
  • Payment. T/T and L/C accepted; sample orders by prior arrangement.

Documents

Download TDS (PDF) Request MSDS

The technical data sheet restates the typical property table above for purchasing and QA files. A GHS safety data sheet is issued per model on request, because classification follows the exact grade and the destination regulation.

Related

More Silicone & Ether Products

Markets

Buying from Southeast Asia?

The same grades are quoted to converters and formulators in Vietnam, Cambodia and Laos; each market page covers the foam problems we are usually asked about there.

Send us your foam system

Base chemistry, temperature, shear and current dosage. Our technical team will run a shake-down trial and recommend a model and a dose, normally within 24 hours on working days.